Instructions for 3 ways to replace special bicycle tires

Many cyclists feel they can alleviate the burden of tire perforation by using modern solid tires. In fact they are much lighter than conventional rubber tires when pumped under tension. Do you know how to replace solid tires? Here are the important settings for the fastest you can use and replace.

1. Use Paddle (lever)

Remove the valve to remove the compressed air from the outside of the tire, remove the tire from the rim.

Install an iron lever blade, or any tool with a slender handle without sharp edges, under the tire lip.

Some Bicycle shops will be included with the paddle when the tire is purchased or sold separately. If you don’t have one, just find an object with a stiffness and strength that you can use as a lever.

Use one or more of the levers to pull around the tire, where it comes away from the nearest edge and slowly pull off the rim. Start by placing the wheel on the edge by hand. Make any selections along the rim and do your best to squeeze the tire out of the rim.

Install the tire in place, the tire lip is placed on the rim of the rim in one position, which can be forced or pressed into that position with your hand to keep it from sliding out of the installation. If you do not have a lanyard in place that can be fastened to the tape. If the tire section continues to pop out as you install it, use as many ties of the levers as possible to be able to. force each component of the tire to be tighter.

You can wash the rim with optional soap and water when doing the installation some tires are harder to install than others. If you are having trouble pulling the tires, mix hand soap with liquid soap or soap and half cup water. Wipe up the rim before you continue with the installation.

Check that your tire is in the correct margin size. Measure your rim width using the clamp and can compare the results with product information for your tire section.

The remaining space between the tire and the rim is difficult at this point in tension. Use the lever to place the paddle between the middle part of the tire and the rim. Hold the rim firmly and use the lever upwards to pull the tire up the rim. Once it gets to the rim, loop with the rest of the tire until all of this is neatly placed on the rim. Make your way around slowly, stretching only over the next few inches at a time.

2. Method Using Vise

Follow the instructions above until you reach the halfway point.

Open the valve knob of the rubber tire, push and insert the tire, no tightening required.

Continue to hold the starting position with one hand and keep the vise head in the last position, the tire clamped in the visa for a few inches at which time the air has been released. Try to use the tool to come in contact with the tire.

Move your hand to the new starting position, repeat this until the tire is completely on the rim.

After both wheels have been replaced, do a reinstallation of your wheels and bike so they never puncture again.

3 .The method of using the tire bar

Find this model for sale as a tire installation tool. There are many different products that are labeled “tire installation tool.” For this method you will need one that looks like a long metal rod with a “guide mount”. The mounting guide has a curve that is the same width as the line of your car, so the tire can fit it.

Look for this from companies that sell rubber tires or tires without grooves.

Make sure a portion of the tire is in contact with the edge. After removing the old tire and tube, install a part of the tire in a safe position with a zip tie.

Attach the bar to the shaft. Fits the end of the bar on the wheel shaft or the express head. The rod should rotate freely around the wheel without having to detach.

Slide the mounting guide to the bar. The mounting rod direction must face the same direction as the rim direction.

Slide the tire into the mounting bar. Install a loose tire part in the mounting guide. Slide the mounting bar up near the edge, so the tires remain taut and securely in the mounting rod.

Rotate the bar to slide the tire to the rim. As you rotate the bar around the wheel, slide the tire away from the mounting guide and onto the rim. Once the tire is in place, this tool should do most of the job for you.

Verify that the tires are in place. If there are any loose areas, press them down or push them into place with a plastic or rubber mallet. Once done, remove the lanyard and reattach the wheels to the bike.

Check the size of the tire you ordered, especially the width and rim width. Doing the wrong thing will take time and money, shipping the wrong order back.

There are other types of installation tools for air tires, but most are for wheelchairs. Some still work, but read the setup guide before buying to make sure it will fit the size of your tire, and you can mount your bike tire on the wheelchair tool (if needed).

If you do not have knowledge of installation please consult these immediately bicycle consultant from top experts or cyclists to hone your mechanical repair experience.

>> Maybe you are interested: A guide to basic bike maintenance before and after the trip for newbies